Lighting & heat
Best radiant heat panels for reptiles
A panel gets screwed to the ceiling of an enclosure and then left alone for years. That makes the figures a maker publishes before you install it the whole purchase - and in this category only one maker publishes them.
By Brijon M.Last updated
Buy the Vivarium Electronics panel in the wattage its published mapping gives for your cage, mount it with the lens at least 6 in from anything, and run it on a proportional thermostat with the probe under the panel. It is the only panel we found that publishes a cage size per wattage, a lens temperature of about 175-200 F, a clearance figure and a thermal fuse. The REPTI ZOO 30 w is the budget option for a small enclosure. What no panel does is produce a bearded dragon basking surface at 108-113 F (42-45 C) surface temperature - a panel is warm-side and ambient heat. It can carry a ball python warm hide at 86-90 F (30-32 C).

Shed & Bask earns a commission from qualifying Amazon purchases made through links on this page. It does not change what we recommend or the order we rank things in. Read the full disclosure.
How we picked
Every pick below is scored against these thresholds, stated as numbers. Publishing them is the point: of the competitor roundups we surveyed, not one published a numeric selection threshold.
Published mounting clearance
A stated minimum distance between the lens and any enclosure surface or animal perch - 6 in in the only published instruction we found - so the panel is installed to a figure rather than by eye
Published lens surface temperature
A stated surface figure at full power - about 175-200 F where it is published - so contact risk and clearance can be judged before the panel is bolted in
Runs on an external thermostat
Designed for a separate thermostat with the probe at the animal's level, with no on-unit dial presented as a substitute for one
Source: ReptiFiles - Ball Python Humidity & Temperature Requirements
Published wattage-to-enclosure mapping
A stated cage size for each wattage, so a 4 x 2 x 2 is matched to a figure instead of guessed at from gallons
Named over-temperature protection
A named cut-out - a thermal fuse or a stated shutdown temperature - and the maker stating plainly that it is not temperature control
Source: National Fire Protection Association - Heating equipment and home fire safety
Holds a published species figure under control
Can hold a ball python warm hide at 86-90 F or a crested gecko top-of-enclosure figure of 82-85 F on a thermostat, and is not sold as a bearded dragon basking source at 108-113 F
Source: ReptiFiles - Ball Python Humidity & Temperature Requirements
These are the same criteria every roundup on this site applies. See the full methodology.
Quick picks
Every row is scored against the published criteria below. Tap a row to read the full write-up.
| # | Product | Best for | Criteria met | Price |
|---|---|---|---|---|
| 1 | ![]() Vivarium Electronics Radiant Heat Panel Best overall, and the only fully documented panel | Ceiling-mounted ambient heat in a PVC enclosure, on a proportional thermostat | 6/6 | Check price on Amazon#ad We may earn a commission. Price and stock are resolved at Amazon. |
| 2 | ![]() Oiibo Reptile Heat Panel Most heated area, with one unresolved warning | Warming a large enclosure cheaply, if you accept on-unit control | 0/6 | Check price on Amazon#ad We may earn a commission. Price and stock are resolved at Amazon. |
| 3 | ![]() REPTI ZOO Reptile Heat Panel Budget pick, for a small enclosure only | A small, short enclosure in a room that only runs a few degrees cold | 0/6 | Check price on Amazon#ad We may earn a commission. Price and stock are resolved at Amazon. |
What a radiant heat panel is, and the one job it is better at than anything else
A radiant heat panel is a flat heating element in a rigid housing that screws to the ceiling of an enclosure and radiates downward. It produces no light. It has no filament to fail, no glass to shatter and - this is the part that matters - no clamp. The single biggest hardware risk in reptile keeping is a hot lamp in a clamp fixture working loose and landing in dry substrate, which is why our heat lamp fire safety page exists. A panel bolted to a ceiling cannot do that. For a keeper whose first filter is what can go wrong rather than what it costs, that is the argument, and it is a good one.
The second argument is shape. A lamp makes a hot spot; a panel warms a broad area below it fairly evenly. For a snake that needs a warm hide rather than a basking beam, or an arboreal gecko that needs the top third of a tall enclosure a few degrees warmer than the bottom, broad is the correct shape of heat. For a desert lizard that needs a small intensely hot surface to lie on, broad is the wrong shape, and no wattage fixes that.
The four figures that separate these three panels
Every panel on the market will get warm. What varies - and varies enormously - is how much of the installation the maker is prepared to specify. We scored on six thresholds, and the table below is the short version: the figures each maker publishes, and the ones it does not.
| Figure | Vivarium Electronics | Oiibo | REPTI ZOO |
|---|---|---|---|
| Wattages | 40 w, 80 w, 120 w | 30 w, 60 w | 30 w |
| Cage size per wattage | Published for all three (2 x 4 ft up to 2 x 6 ft and larger) | Max enclosure 48 x 24 x 24 in for the 60 w (listing) | Not published; listing says heat under a third of the floor |
| Lens surface temperature | About 175-200 F at full power | Not published | Not published |
| Minimum clearance | At least 6 in from any cage surface | Not published | Not published |
| Over-temperature cut-out | Self-resetting thermal fuse, stated not to be a thermostat | Not published | Not published |
| External thermostat | Required; proportional recommended, probe under the panel | Listing forbids it in one place and permits it in another | Not stated either way |
| Housing | Noryl, stated flame retardant | ABS | Not published |
Read down the first column and you are reading an installation manual. Read down the other two and you are reading a product description. That gap is the whole ranking, and it is not a matter of brand loyalty: if either budget maker published a clearance figure and a lens temperature tomorrow, the scores would change.
Sizing: match the wattage to the cage, then to the room
Panel wattage is not a species decision. It is a decision about the gap between your room temperature and the figure you are trying to hold inside the enclosure, which is why the only published mapping we found names both. Vivarium Electronics states 40 w for a 2 x 4 ft cage no taller than 12 in in a room at 75 F or above; 80 w once the cage is over 12 in tall, runs to 2 x 6 ft, or sits in a room below 74 F; and 120 w for 2 x 6 ft and larger, open-air enclosures or cool rooms.
Put the most common enclosure on this site through that: a 4 x 2 x 2 PVC enclosure is 24 in tall, so it is past the 12 in line, and 80 w is the starting point rather than 40 w in a normal room. In a cold garage or an unheated spare room, the 120 w is the honest choice even at that footprint. If your enclosure is a tall arboreal build - an 18 x 18 x 36 in terrarium for a crested gecko - the panel heats the top, which is where that animal wants its 82-85 F (28-29 C) at the top of the enclosure anyway, and the bottom stays at its 70-75 F (21-24 C) at the bottom.
Oversizing is the common mistake and it is not harmless. A panel that is too big spends its life switching off, which means the enclosure cycles between the setpoint and something cooler instead of sitting at a figure. Undersizing shows up as a panel that never switches off and still misses the target on the coldest night of the year. Both are measurement problems, which is why the order of operations on this site always starts with a thermometer - see best reptile thermometers and hygrometers for what to buy and how to measure basking temperature for where to point it.
The thermostat question, and the panel that says no
Every heat source on this site is assumed to be on a thermostat. That is not a preference. A heating element with no external control runs until it reaches equilibrium with the room, and the room changes. Panels are no exception - the published guidance for the one documented panel here is explicit that it is designed for a thermostat, and recommends a proportional unit with the probe mounted under the panel so it regulates the temperature at the animal rather than at the ceiling.
Which makes the Oiibo listing a genuine problem rather than a nitpick. It carries the sentence that the panel must never be used with a thermostat or timer, and also the sentence that a thermostat can be used to reach the appropriate temperature. We are not going to guess which one the manufacturer means. If you buy it, you are relying on an unscaled knob and your own measurements, and you should treat the enclosure as unmonitored until you have watched it through a cold night with a probe thermometer in place.
Clearance, contact and what the fuse is actually for
The published lens figure of about 175-200 F at full power is the number that makes the 6 in clearance rule make sense. That is hot enough to burn an animal that can press against it and hot enough to matter to anything flammable nearby, which is why the instruction is a distance rather than a suggestion. The maker also notes that mounting closer than 6 in can push the panel past its own fuse temperature - so the clearance rule protects the panel as well as the animal.
The self-resetting thermal fuse is worth understanding before you rely on it. It cuts power if the panel's internals exceed safe operating temperature, and the maker states in plain language that it is for extreme situations and is not a thermostat. Treat it as the smoke alarm, not the thermostat. The thing that keeps the enclosure at a figure is the controller you bought separately.
One more clearance case that catches people out: branches and hides. Six inches from the cage surface is not six inches from the top of a cork round or a climbing branch the animal uses. Measure the gap from the lens to the highest thing an animal can stand on, not from the lens to the floor. For an arboreal species that will be the top perch, and that is exactly where a crested gecko will choose to sit, because the top is the warm part.
Which species a panel suits, and which it does not
| Species | Published target | Panel fit |
|---|---|---|
| Bearded dragon | 108-113 F (42-45 C) surface temperature basking surface | Poor as the primary heat source - no panel makes a basking surface. Usable as ambient or cold-room support alongside a basking lamp |
| Leopard gecko | 94-97 F (34-36 C) surface; warm hide 90-92 F (32-33 C) | Workable for ambient warmth in a cold room, but the published figure is a warm floor - a thermostatically controlled mat is the direct answer |
| Ball python | Warm hide 86-90 F (30-32 C) | Strong fit. A warm hide figure is an area figure, which is what a panel produces, and the snake cannot coil around a ceiling-mounted element |
| Crested gecko | 82-85 F (28-29 C) at the top of the enclosure | Strong fit in a cold room, with a hard ceiling: 85 F sustained is the top of the published range, so the probe placement matters more than the wattage |
The ball python case is the one that sells panels, and it is the one we would buy for. The published figure is a warm hide at 86-90 F (30-32 C) per ReptiFiles, with the cool end published alongside it as Cool hide 72-80 F (22-27 C); air never above 95 F (35 C). A panel over one end of a 4 x 2 x 2, on a proportional thermostat with the probe in the warm hide, produces exactly that - and nothing inside the enclosure is hot enough to injure a snake that decides to investigate it. Our ball python heating page sets out the full warm-end build.
Install reality: a panel needs a ceiling
This is where plenty of panel purchases fail. A radiant panel screws into a solid top. A front-opening PVC enclosure has one. A glass terrarium with a mesh lid does not - there is nothing structural to screw into, the mesh sags, and a panel suspended above mesh loses a chunk of its output to the room. If you keep in a screen-top glass tank, the honest options are a guarded overhead emitter or a projector in a rated fixture above the screen, and our best reptile heat lamp fixtures page is the fixture side of that decision.
The documented panel also ships without a plug on the cord so that it can be routed through a small hole in the cage, which the maker states takes about five minutes with a Phillips screwdriver. That is fine if you are comfortable drilling your own enclosure and a dealbreaker if you are not. The two budget panels mount under the lid with screws and come ready to plug in, which is the single practical advantage they have.
What a panel costs to run, and why that is the wrong first question
Panels are often sold on efficiency. In practice a 40 w panel and a 40 w emitter put the same 40 watts of electricity into your room, and on a thermostat both draw only as much as they need to hold the setpoint - so the real driver of running cost is the gap between your room temperature and your target, not the technology. Our reptile lighting and heating running costs page does that arithmetic properly with published electricity figures rather than guesses.
Which leads to the most useful thing on this page: measure your room overnight for a week before buying anything. Bearded dragon tolerates 55-75 F (12-24 C) at night, and for leopard gecko the published note is "Tolerates a drop to 60 F (16 C)". A surprising number of keepers shopping for night heat do not need it, and a panel bought for a problem the room does not have is a hole drilled in an enclosure for nothing.
How we picked, and what we did not do
We did not bench-test these panels, and no page on this site claims otherwise. Every figure above is quoted from the maker's own published information where one exists - fetched for this page on 15 November 2026 - and from the retail listing where it does not, which the spec rows say explicitly. Where nothing is published we wrote "not published" instead of borrowing a figure from a review site.
That method decides the ranking. All three panels will warm an enclosure. They are separated by how much of the installation you can verify before an animal is living under it, which in a category of permanently-mounted electrical heaters is the right axis. Our methodology page states the standard in full.
Two products were checked and are not ranked here. Zoo Med's ReptiTherm Habitat Heater is a floor or side-mounted heater in a polyethylene case with a stated 119 F thermal shut-off, built for heavy tortoises - a different device for a different job, not a ceiling panel. And several unbranded marketplace panels appear in the same search results with no manufacturer, no spec page and no named approval; we will not put a reader's animal under one of those on the strength of a listing photo.
Alternatives worth checking before you buy a panel
A ceramic heat emitter. Cheaper, no drilling, and the same lightless ambient heat - at the cost of needing a guarded fixture because the element is reachable. Best ceramic heat emitters scores three of them, and radiant heat panel versus ceramic heat emitter runs the head-to-head.
A deep heat projector. Lightless like a panel, but it projects Infrared A and B in a beam, and one maker publishes a temperature-at-distance table you can aim with. Best deep heat projectors is that page.
A thermostatically controlled heat mat, if what you actually need is a warm floor rather than warm air - and for a leopard gecko that is usually the case. Best heat mat for a leopard gecko scores four.
The order we would buy in
Thermometer first, then a week of overnight readings. If the room genuinely falls short: the Vivarium Electronics panel in the wattage its mapping gives for your cage, a proportional thermostat with the probe under the panel at the animal's level, 6 in of clearance from the highest thing an animal can climb, and three days of infrared readings before you trust it. For the wider question of which heat source class belongs in your build at all, best heat sources ranks the categories rather than the models.
The controller this page assumes
Spyder Robotics Herpstat 1 Proportional Thermostat
A proportional thermostat is what the only documented panel here asks for, and proportional control is what keeps a panel sitting at a figure instead of cycling around it.
The picks in full

1. Best overall, and the only fully documented panel
Vivarium Electronics Radiant Heat Panel
Vivarium Electronics · Ceiling-mounted ambient heat in a PVC enclosure, on a proportional thermostat
It is the only panel here that answers all six questions in writing, and in a category where the device is bolted above an animal and left running, that is the product. A cage size for every wattage - 40 w for a 2 x 4 ft cage no taller than 12 in at 75 F room temperature, 80 w for a taller cage or a cooler room, 120 w for 2 x 6 ft and up. A lens that runs about 175-200 F at full power, published, so you can judge clearance instead of touching it. A 6 in minimum gap between the lens and anything else. A self-resetting thermal fuse, with the maker stating plainly that the fuse is not a thermostat. And a named controller recommendation - a proportional unit with the probe under the panel. The cost of all that documentation is a harder install: it mounts inside the cage top with screws and the cord goes through a hole you drill.
Specifications
- Wattages
- 40 w, 80 w and 120 w (dealers also list a 28 w)
- Sizing
- Vivarium Electronics states 40 w for a 2 x 4 ft cage no taller than 12 in at a room temperature of 75 F or above; 80 w for 2 x 4 ft to 2 x 6 ft, a cage over 12 in tall, or a room below 74 F; 120 w for 2 x 6 ft and larger, open-air cages or cool rooms
- Lens temperature
- Approximately 175-200 F on the lens surface at full power
- Over-temperature
- Self-resetting thermal fuse, which the maker states is not a thermostat
- Clearance
- Lens at least 6 in from any cage surface; a closer mount can trip the fuse
- Control
- Designed for a thermostat; the maker recommends a proportional unit (VE-200 or VE-300) with the probe mounted under the panel
- Housing
- Noryl shell, described as odorless, flame retardant and strong at high temperatures
- Install
- Mounts inside the cage top with three stainless steel screws; ships without a plug, so the cord passes through a drilled hole
- Care
- Not to be submerged; new panels may need a 6-24 hour burn-in for manufacturing odor
How it scored against our criteria
| Published mounting clearanceA stated minimum distance between the lens and any enclosure surface or animal perch - 6 in in the only published instruction we found - so the panel is installed to a figure rather than by eye | Meets |
|---|---|
| Published lens surface temperatureA stated surface figure at full power - about 175-200 F where it is published - so contact risk and clearance can be judged before the panel is bolted in | Meets |
| Runs on an external thermostatDesigned for a separate thermostat with the probe at the animal's level, with no on-unit dial presented as a substitute for one | Meets |
| Published wattage-to-enclosure mappingA stated cage size for each wattage, so a 4 x 2 x 2 is matched to a figure instead of guessed at from gallons | Meets |
| Named over-temperature protectionA named cut-out - a thermal fuse or a stated shutdown temperature - and the maker stating plainly that it is not temperature control | Meets |
| Holds a published species figure under controlCan hold a ball python warm hide at 86-90 F or a crested gecko top-of-enclosure figure of 82-85 F on a thermostat, and is not sold as a bearded dragon basking source at 108-113 F | Meets |
What works
- Publishes a cage size for every wattage, which is the sizing figure no other panel maker states
- A stated lens temperature of about 175-200 F at full power, so clearance and contact risk can be judged before buying
- A self-resetting thermal fuse, and the maker is explicit that it is a last-ditch cut-out rather than temperature control
- The 6 in clearance rule is published as a number, so installation is to a figure instead of by eye
- Ceiling mounting removes the clamp-failure mode that puts a hot lamp in the substrate
What to know
- Ships without a plug and expects a cord routed through a hole you drill - this is not a five-minute tank accessory
- The proportional thermostat the maker recommends is a second purchase and the more expensive controller type
- Nothing here produces a bearded dragon basking surface at 108-113 F; a panel is ambient and warm-side heat
- Mounting closer than 6 in, or resting it lens-down while plugged in, can void the warranty and damage the panel
- No published voltage, dimensions or warranty term on the maker's FAQ, so the box is where you confirm fit
Who should look elsewhere
If your enclosure has a screen top rather than a solid ceiling there is nothing to screw the panel to - a guarded overhead lamp or emitter is the honest answer. If what you need is a warm floor for a leopard gecko, buy a thermostatically controlled mat instead.

2. Most heated area, with one unresolved warning
Oiibo Reptile Heat Panel
Oiibo · Warming a large enclosure cheaply, if you accept on-unit control
The 60 w version is 17.7 in across and its seller names a maximum enclosure - 48 x 24 x 24 in - which is more than the other budget panel will tell you. It is also the one pick on this page we cannot recommend running the way this site runs every heat source, because its own listing says the panel must never be used with a thermostat or timer, and then says a thermostat can be used to reach the right temperature. Those two sentences are on the same listing. Until the seller resolves that, you are buying a heater controlled by an unscaled knob, and the only way to know what it is doing is to measure the enclosure yourself every time you touch it. Ranked second on coverage and documentation of size, not on control.
Specifications
- Models
- 30 w (AH02) and 60 w (AH02P)
- Enclosure guidance
- The 60 w listing gives a recommended maximum enclosure of 48 x 24 x 24 in (120 x 60 x 60 cm)
- Size
- 17.7 in wide, 1.2 in deep (60 w; listing figures, which disagree on the second dimension)
- Material
- ABS
- Power
- 100-120 V, 60 Hz
- Control
- Knob on the unit - the listing says rotate left to lower and right to raise, with no scale or setpoint published
- Thermostat
- The listing states the panel must never be used with a thermostat or timer, and elsewhere on the same listing says a thermostat can be used to reach the right temperature. The contradiction is unresolved by the seller
- Mounting
- Mounts under the lid with screws
- Fan
- Built-in fan
How it scored against our criteria
| Published mounting clearanceA stated minimum distance between the lens and any enclosure surface or animal perch - 6 in in the only published instruction we found - so the panel is installed to a figure rather than by eye | Not published |
|---|---|
| Published lens surface temperatureA stated surface figure at full power - about 175-200 F where it is published - so contact risk and clearance can be judged before the panel is bolted in | Not published |
| Runs on an external thermostatDesigned for a separate thermostat with the probe at the animal's level, with no on-unit dial presented as a substitute for one | Below |
| Published wattage-to-enclosure mappingA stated cage size for each wattage, so a 4 x 2 x 2 is matched to a figure instead of guessed at from gallons | Partial |
| Named over-temperature protectionA named cut-out - a thermal fuse or a stated shutdown temperature - and the maker stating plainly that it is not temperature control | Not published |
| Holds a published species figure under controlCan hold a ball python warm hide at 86-90 F or a crested gecko top-of-enclosure figure of 82-85 F on a thermostat, and is not sold as a bearded dragon basking source at 108-113 F | Partial |
What works
- The largest heated area here, and the only panel on this page whose listing names a maximum enclosure size - 48 x 24 x 24 in for the 60 w
- Two wattages, so a 30 w can serve a smaller build in the same mounting style
- Published voltage and frequency, which the other budget panel does not state
- Lightless, so it can run overnight without breaking the photoperiod
What to know
- The listing both forbids and permits a thermostat; until that is resolved by the seller, you are buying a heater you cannot confidently control externally
- No published surface temperature, no published clearance and no named over-temperature cut-out
- A knob with no scale is not a setpoint - the only way to know what it is doing is to measure the enclosure yourself, every time you touch it
- Dimensions differ between two versions of the same listing, so the panel you receive may not be the one you measured for
- Review volume is low and ratings are mixed, so there is little field history to lean on
Who should look elsewhere
If you want a panel under thermostat control - which is how every heat source on this site is run - buy the documented panel and a proportional controller. If the enclosure is a screen-top glass tank, a guarded overhead emitter is the simpler install.

3. Budget pick, for a small enclosure only
REPTI ZOO Reptile Heat Panel
REPTI ZOO · A small, short enclosure in a room that only runs a few degrees cold
The budget pick and the smallest unit here: 30 w in a 9 x 6 in case with a fan, mounted under the lid. The one genuinely good instruction on its listing is that the heated area should stay under a third of the enclosure, which is the right instinct - you are heating a zone, not a box. Everything else is missing. There is no manufacturer spec page at all, so there is no published lens temperature, no clearance figure, no over-temperature cut-out and no statement about whether an external thermostat may be used. For a short enclosure in a room that runs a couple of degrees cold it will do the job. For an enclosure where a figure has to be held, buy the panel that publishes its numbers.
Specifications
- Wattage
- 30 w
- Size
- 9.12 x 5.98 x 1.16 in (retailer listing figure; the maker publishes no spec page)
- Control
- Adjustable temperature dial on the unit itself
- Fan
- Integrated fan, described on the listing as spreading heat and as a safety feature
- Mounting
- Mounts under the enclosure lid
- Coverage guidance
- The listing for the under-lid version states the heating area should be less than one third of the enclosure and that ventilation prevents heat accumulation
- Lens temperature
- Not published
- Thermostat
- Not stated either way; REPTI ZOO sells a separate dimming controller rated to 300 w
How it scored against our criteria
| Published mounting clearanceA stated minimum distance between the lens and any enclosure surface or animal perch - 6 in in the only published instruction we found - so the panel is installed to a figure rather than by eye | Not published |
|---|---|
| Published lens surface temperatureA stated surface figure at full power - about 175-200 F where it is published - so contact risk and clearance can be judged before the panel is bolted in | Not published |
| Runs on an external thermostatDesigned for a separate thermostat with the probe at the animal's level, with no on-unit dial presented as a substitute for one | Not published |
| Published wattage-to-enclosure mappingA stated cage size for each wattage, so a 4 x 2 x 2 is matched to a figure instead of guessed at from gallons | Partial |
| Named over-temperature protectionA named cut-out - a thermal fuse or a stated shutdown temperature - and the maker stating plainly that it is not temperature control | Not published |
| Holds a published species figure under controlCan hold a ball python warm hide at 86-90 F or a crested gecko top-of-enclosure figure of 82-85 F on a thermostat, and is not sold as a bearded dragon basking source at 108-113 F | Partial |
What works
- The lowest-cost entry to a ceiling-mounted lightless heat source, which is the right shape of heat for a snake or a crepuscular gecko
- The one-third-of-the-floor guidance on the listing is the correct instinct: a heated zone, not a heated enclosure
- A fan keeps the case temperature down, which matters if an arboreal animal can climb to the ceiling
- Small enough to fit a short enclosure where a 40 w panel would be too much heat
What to know
- No manufacturer spec page at all - every figure here comes off a retail listing, which is a weak basis for a device that runs unattended
- No published surface temperature and no published clearance, so there is no number to install to
- A dial on the unit is not a thermostat with a probe at the animal's level, and nothing on the listing says whether an external controller may be used
- A fan is a moving part in a warm, dusty enclosure - one more thing that can stop without announcing itself
- 30 w is a small budget of heat; in a cold room it will run flat out and still miss the figure
Who should look elsewhere
If the panel has to hold a figure rather than take the edge off a room, buy the panel that publishes its numbers and run it on a proportional thermostat. If you need a basking surface, this is the wrong category entirely.
Frequently asked questions
What is the best radiant heat panel for reptiles?
The Vivarium Electronics panel, because it is the only one that publishes a cage size per wattage, a lens surface temperature of about 175-200 F, a 6 in minimum clearance and a self-resetting thermal fuse - and states that the fuse is not a thermostat. The REPTI ZOO 30 w is the budget option for a small, short enclosure. Both need an external thermostat.
What size radiant heat panel do I need for a 4x2x2?
Start at 80 w. The only published mapping we found puts 40 w on a 2 x 4 ft cage no taller than 12 in at a room temperature of 75 F or above, and moves to 80 w once the cage is taller than 12 in or the room is below 74 F. A 4 x 2 x 2 is 24 in tall, so it is past that line. In a cold room, 120 w is the honest choice.
Do radiant heat panels need a thermostat?
Yes, and the documented panel in this roundup says so itself - it is designed for a thermostat, with a proportional unit recommended and the probe mounted under the panel. A dial on the panel is not a thermostat: it sets how hard the element runs rather than holding the temperature where the animal is.
How far should a radiant heat panel be from the animal?
The only published clearance figure in this category is at least 6 in between the lens and any cage surface, and the maker notes that a closer mount can trip the panel's own thermal fuse. Measure that 6 in to the highest thing an animal can stand on - a branch or a tall hide - not to the enclosure floor.
Can a radiant heat panel replace a basking lamp for a bearded dragon?
No. Bearded dragon needs a basking surface at 108-113 F (42-45 C) surface temperature, which is a small intensely hot surface produced by a bright overhead lamp. A panel heats an area to an ambient figure. A panel can support a dragon enclosure in a cold room, but it cannot be the basking source.
Can I use a radiant heat panel on a glass tank with a mesh lid?
Not well. A panel screws into a solid ceiling; a mesh lid gives it nothing structural to fix to, and suspending one above mesh loses output to the room. In a screen-top tank, a guarded emitter or a projector in a rated fixture above the screen is the practical route.
Sources
- VE Radiant Heat Panel FAQ - sizing, lens temperature, clearance and thermal fuse — Reptile Basics / Vivarium Electronics
- ReptiTherm Habitat Heater product information — Zoo Med Laboratories
- Ball Python Humidity & Temperature Requirements — ReptiFiles
- Bearded Dragon Temperatures & UVB Requirements — ReptiFiles
- Crested Gecko Temperatures & Humidity — ReptiFiles
- Heating equipment and home fire safety — National Fire Protection Association
Read next

Hub
Reptile UVB, heat and thermostats
Wattage and percentage tell you almost nothing on their own. UV index at a stated mount distance is the number that decides whether a lamp is right for your animal.

Lighting & heat
Radiant heat panel vs ceramic heat emitter
The two lightless ambient heat sources compared on mounting, burn risk and controller type - plus why neither is a basking lamp.

Lighting & heat
Best deep heat projectors for reptiles
Three named deep heat projectors scored on published infrared claims, controller guidance, temperature at distance, fixture requirements and zone size.

Lighting & heat
Best ceramic heat emitters
Three named ceramic heat emitters scored on published wattage mapping, fixture approval, thermostat guidance and service life.

Lighting & heat
Best reptile thermostats (2026)
Thermostats ranked by control type, stated accuracy, load ceiling and whether they alarm on failure.

Ball python
Ball python heating requirements
Ball python heating: the hide figures, the air ceiling, and the two-bulb rule.